Study in Pictures🌐 English (New Zealand)
NZ Plumbing Exam Illustrated

Digital book in PDF · read it on your phone or print it

NZ Plumbing Exam Illustrated

Water supply, hot water, backflow, traps and vents, falls, drain layout, stormwater and pressure testing. Each topic has its own page: the drawing first, then what you need to remember.

  • 64 illustrated pages
  • English
  • 30-day guarantee
NZ$ 39NZ$ 89
Get the book · NZ$ 39

Price shown for: New Zealand. In other countries, the checkout shows the price that applies there.

About this book

What it is

Water supply, hot water, backflow, traps and vents, falls, drain layout, stormwater and pressure testing. Each topic has its own page: the drawing first, then what you need to remember.

Who This Book Is For
  • You're finishing your apprenticeship
  • The exam is coming up
  • You already work as a plumber
What it covers
  1. How the exam and the code fit together
  2. Reading and drawing plumbing
  3. Cold water supply
  4. Hot water
  5. Backflow prevention
  6. Sanitary plumbing: fixtures, traps and vents
  7. Drainage and stormwater
  8. Testing, commissioning and exam revision
Language
English (New Zealand)
Pages
64
Format
Digital book in PDF · read it on your phone or print it
Price
NZ$ 39 (New Zealand)
Delivery
This is a digital PDF book sent to your email: nothing is printed or shipped.
30-Day Guarantee
30-day guarantee: if a file doesn't open, if the content isn't what the product page describes, if you were charged twice or the email never arrived, write to us and we'll refund you in full.

Look Inside the Book

Registration exam: pass mark 60%, no rounding up.
Registration exam: pass mark 60%, no rounding up.
Plan for drains, section for traps and vents, isometric for pipework, elevation for heights.
Plan for drains, section for traps and vents, isometric for pipework, elevation for heights.
Main, toby, point of supply, boundary isolating valve, fixtures: the route in one drawing.
Main, toby, point of supply, boundary isolating valve, fixtures: the route in one drawing.
Under 120 kPa = low pressure; above it, every mains-pressure cylinder needs a TPR valve.
Under 120 kPa = low pressure; above it, every mains-pressure cylinder needs a TPR valve.
High could kill, medium endangers health, low is a nuisance
High could kill, medium endangers health, low is a nuisance
3 m at 1:40 = 75 mm fall = 2.5 %; at 1:60 it's 50 mm
3 m at 1:40 = 75 mm fall = 2.5 %; at 1:60 it's 50 mm
At 100 mm/h, a 100 mm downpipe drains about 210 m² of roof
At 100 mm/h, a 100 mm downpipe drains about 210 m² of roof
G12/AS1 pressure test: 1500 kPa for at least 15 minutes, no leaks
G12/AS1 pressure test: 1500 kPa for at least 15 minutes, no leaks

Take a Look at the 8 Parts and 60 Topics

How the exam and the code fit together

pp. 5-10
  1. What the licensed plumber exam asks you to show
  2. Building Act, Building Code, Acceptable Solution: three layers
  3. Means of compliance: AS, VM or alternative
  4. The clauses a plumber lives in: G12, G13, E1
  5. Sanitary plumbing as restricted work
  6. Consent, inspection and the code compliance certificate

Reading and drawing plumbing

pp. 11-16
  1. Plan, elevation, section, isometric
  2. Plumbing symbols you must recognise
  3. Drawing an isometric in five steps
  4. Labelling a diagram so it gets the marks
  5. DN, OD and ID are not the same number
  6. Metric conversions a plumber uses

Cold water supply

pp. 17-24
  1. From the main to the tap
  2. Supply pressure and pressure limiting valves
  3. Sizing a cold water pipe
  4. Pipe materials: copper, PEX, PE and their joints
  5. Supporting pipework: clip spacing
  6. Water hammer and how to stop it
  7. Frost, insulation and buried pipes
  8. Rainwater tanks and dual supplies

Hot water

pp. 25-33
  1. Low-pressure, mains-pressure, instantaneous
  2. Storage at 60 °C: the Legionella rule
  3. Delivery temperature: 55 °C and 45 °C
  4. Tempering valves against thermostatic mixing valves
  5. The valve train on a mains-pressure cylinder
  6. Relief valve drains: where they discharge
  7. Seismic restraint of water heaters
  8. Sizing hot water storage
  9. Heat pumps, solar and wetbacks

Backflow prevention

pp. 34-40
  1. Backflow: back-pressure and back-siphonage
  2. Cross connections you see on real jobs
  3. Hazard ratings: high, medium, low
  4. Matching the device to the hazard
  5. The air gap: twice the outlet diameter
  6. Containment, zone and individual protection
  7. Testable devices and annual testing

Sanitary plumbing: fixtures, traps and vents

pp. 41-49
  1. What a trap does and why it fails
  2. Trap types and fixture connections
  3. Discharge units and pipe sizing
  4. Fall on a discharge pipe in mm and percent
  5. Maximum length of an unvented branch
  6. Vent pipes: what they do and where they go
  7. Single stack against fully vented systems
  8. Air admittance valves: when they are allowed
  9. Fixture outlets: WC pan, shower waste, floor waste

Drainage and stormwater

pp. 50-57
  1. Sanitary drain layout in plan
  2. Gully traps: the New Zealand detail
  3. Overflow relief gully: the height rule
  4. Drain gradients and calculating levels
  5. Bedding, cover and trench detail
  6. Inspection points and access
  7. Stormwater: spouting, downpipes, discharge
  8. Septic tanks and on-site systems

Testing, commissioning and exam revision

pp. 58-64
  1. Pressure testing a water supply
  2. Testing sanitary pipework and drains
  3. Commissioning a hot water system
  4. Answering a diagram question step by step
  5. Calculation questions: the method that doesn't change
  6. Numbers to have at hand
  7. The most frequent mistakes, drawn wrong and right

Who This Book Is For

You're finishing your apprenticeship

Every topic from your course notes on its own drawn page, so revising means looking, not rereading.

The exam is coming up

Diagram and calculation questions with a method that stays the same every time, plus practice questions with worked answers.

You already work as a plumber

On a limited certificate or trained overseas: the NZ rules, metric falls and backflow, drawn so you can check them at a glance.

Plus: 2 Free Books

Plumbing Exam Practice Questions with Worked Answers
BONUS 1

Plumbing Exam Practice Questions with Worked Answers

Short-answer and diagram-style questions with every answer worked through, so you can test yourself before the real paper.

15 Common Plumbing Mistakes, Before and After
BONUS 2

15 Common Plumbing Mistakes, Before and After

The mistakes made most often with falls, vents, traps and backflow, each drawn wrong and then right, to revise at a glance.

30-Day Guarantee

30-day guarantee: if a file doesn't open, if the content isn't what the product page describes, if you were charged twice or the email never arrived, write to us and we'll refund you in full. You pay once. No subscriptions.

Frequently Asked Questions

Is it for me if I've worked on a limited certificate for years, or trained overseas?

Yes. It isn't a beginner's course: it assumes you know the job and focuses on the NZ rules and the way the written exam asks for them, with drawings, labels and metric calculations. If you've done the apprenticeship, use it to revise what you already know, one page at a time.

Where does the content come from?

It's written for New Zealand, not adapted from an Australian book. It follows the NZ Building Code clauses G12, G13 and E1, their Acceptable Solutions, the AS/NZS 3500 parts they cite and the exam prescriptions published by the Plumbers, Gasfitters and Drainlayers Board. NZ terms throughout: toby, point of supply, gully trap, overflow relief gully, metric falls. The drawings and worked examples are our own. Code documents get amended, so check the current version of each one before your exam.

Is it official material?

No. It's an independent study book, not affiliated with or endorsed by the Board, MBIE or Standards New Zealand.

Does it replace my apprenticeship training or course?

No. It's a revision aid to use alongside your training, your work on site and the current code documents. It doesn't give you a certificate or count towards registration: only the Board's exam does that.

Are the practice questions the ones from the exam?

No. They're written for this book, in the style of the exam, including diagram and calculation questions, so you can test yourself and check the worked answers. They aren't official exam questions.

When and how do I get it?

As a PDF by email, to the address you enter at checkout. The 2 bonus books come the same way.

Do I have to pay every month?

No. It's a one-off payment.

Can I have it on paper?

Yes. It's a PDF made to print: print the whole book, or just the pages you want to keep in the van.

How does the refund work?

You have 30 days. We refund everything if the file won't open, if the book isn't what you see on this page, if you were charged twice or if the email doesn't arrive: just email us.

NZ$ 39NZ$ 89
Get the book · NZ$ 39

This is a digital PDF book sent to your email: nothing is printed or shipped.