Study in Pictures๐ŸŒ English (Australia)
Gasfitting Licence Illustrated

Digital book in PDF ยท read it on your phone or print it

Gasfitting Licence Illustrated

Written for Australian gasfitters, in kPa and MJ/h: natural gas and LPG, meter and cylinder location, pipe materials, pipe sizing, soundness testing, Type A appliances, ventilation, flues and commissioning. Every topic has its own page: the drawing first, then what you need to remember.

  • 66 illustrated pages
  • English
  • 30-day guarantee
A$ 39A$ 89
Get the book ยท A$ 39

Price shown for: Australia. In other countries, the checkout shows the price that applies there.

About this book

What it is

Written for Australian gasfitters, in kPa and MJ/h: natural gas and LPG, meter and cylinder location, pipe materials, pipe sizing, soundness testing, Type A appliances, ventilation, flues and commissioning. Every topic has its own page: the drawing first, then what you need to remember.

Who This Book Is For
  • You're an apprentice in your final years
  • Your licence exam is coming up
  • You already do plumbing and gas work
What it covers
  1. Gas Basics for Gasfitters
  2. From Meter or Cylinder to the Pipe
  3. Pipework and Materials
  4. Pipe Sizing Step by Step
  5. Soundness Testing and Purging
  6. Type A Appliances
  7. Ventilation and Flues
  8. Commissioning and Handover
  9. Revision and Exam Prep
Language
English (Australia)
Pages
66
Format
Digital book in PDF ยท read it on your phone or print it
Price
A$ 39 (Australia)
Delivery
This is a digital PDF book sent to your email: nothing is printed or shipped.
30-Day Guarantee
30-day guarantee: if a file doesn't open, if the content isn't what the product page describes, if you were charged twice or the email never arrived, write to us and we'll refund you in full.

Look Inside the Book

Natural gas collects at the ceiling; LPG (propane, about 1.5 ร— air) collects in drains, pits and underfloor.
Natural gas collects at the ceiling; LPG (propane, about 1.5 ร— air) collects in drains, pits and underfloor.
Regulator โ†’ meter โ†’ pipe โ†’ valve โ†’ connector โ†’ appliance โ†’ flame โ†’ flue: one line, eight stops.
Regulator โ†’ meter โ†’ pipe โ†’ valve โ†’ connector โ†’ appliance โ†’ flame โ†’ flue: one line, eight stops.
Copper, steel, PE and multilayer: multilayer never above ground outside a building (cl. 5.3.16)
Copper, steel, PE and multilayer: multilayer never above ground outside a building (cl. 5.3.16)
Length and load eat pressure: the last inlet must still see 1.13 kPa (standard Victorian install).
Length and load eat pressure: the last inlet must still see 1.13 kPa (standard Victorian install).
New installation: zero drop. Allowable leakage only for existing natural gas standard installations up to 30 L.
New installation: zero drop. Allowable leakage only for existing natural gas standard installations up to 30 L.
Type A: certified scheme. Type B: above 10 MJ/h, not Type A, from the manual shut-off valve downstream.
Type A: certified scheme. Type B: above 10 MJ/h, not Type A, from the manual shut-off valve downstream.
Exhaust fans can reverse a flue: find the ventilation needed with the window and smoke test.
Exhaust fans can reverse a flue: find the ventilation needed with the window and smoke test.
Test, purge, pressure, flame, safety, flue, handover: 7 steps in one order.
Test, purge, pressure, flame, safety, flue, handover: 7 steps in one order.

Take a Look at the 9 Parts and 62 Topics

Gas Basics for Gasfitters

pp. 5-11
  1. Natural Gas vs LPG: Which Way It Goes When It Leaks
  2. The Fire Triangle and Flammability Limits
  3. Pressure in kPa: Reading the Numbers Right
  4. Heating Value: Why MJ Matters More Than Cubic Metres
  5. Complete vs Incomplete Combustion
  6. Carbon Monoxide: The Gas You Can't See
  7. Odorant and Gas Detection on the Job

From Meter or Cylinder to the Pipe

pp. 12-19
  1. The Installation Followed the Way the Gas Flows
  2. Where the Network Ends and Your Work Begins
  3. Meter Position and Clearances
  4. LPG Cylinders: The Location Rules
  5. Regulators: Two-Stage LPG and Natural Gas
  6. Automatic Changeover on Twin Cylinders
  7. Isolation Valves: Where They Must Be
  8. Pipework Entering a Building

Pipework and Materials

pp. 20-27
  1. Approved Pipe Materials at a Glance
  2. Copper: Brazing vs Press Fittings
  3. Steel Pipe and Threaded Joints
  4. Polyethylene Underground Only
  5. Burying Pipe: Depth, Bedding and Marker Tape
  6. Pipe Support and Clip Spacing
  7. Concealed Pipe: Walls, Roofs and Underfloor
  8. Flexible Connectors and Bayonet Fittings

Pipe Sizing Step by Step

pp. 28-35
  1. Why Pipe Sizing Is About Pressure Drop
  2. The 5 Sizing Steps, Always in the Same Order
  3. Reading Appliance Input from the Data Plate
  4. Measuring the Index Run
  5. Worked Example: One Cooktop, One Run
  6. Worked Example: Three Appliances on a Branch
  7. LPG vs Natural Gas: Same Pipe, Different Answer
  8. Adding an Appliance to an Existing Installation

Soundness Testing and Purging

pp. 36-42
  1. What a Soundness Test Proves
  2. Setting Up the Test: Gauge, Isolation and Test Point
  3. Soundness Test in Fixed Steps
  4. Temperature and False Results
  5. Finding the Leak: Bubbles, Detector, Sections
  6. Purging Pipework Safely
  7. Recording the Test

Type A Appliances

pp. 43-50
  1. What Makes an Appliance Type A
  2. Reading the Installation Instructions First
  3. Cooktops and Ovens: Clearances Above and Around
  4. Space Heaters: Flued and Unflued
  5. Instantaneous vs Storage Water Heaters
  6. Ducted Heaters: Gas Side Only
  7. Outdoor Appliances and Barbecues
  8. Burner Basics: Injector, Primary Air, Flame

Ventilation and Flues

pp. 51-58
  1. Air for Combustion: Why the Room Matters
  2. Ventilation Openings: High and Low
  3. How a Natural Draught Flue Works
  4. Room-Sealed and Fan-Assisted Flues
  5. Flue Terminals: The Clearances Inspectors Check
  6. Flue Termination Above the Roof
  7. Spillage Test: Checking the Flue Works
  8. Exhaust Fans and Negative Pressure

Commissioning and Handover

pp. 59-62
  1. Commissioning in the Same Order Every Time
  2. Setting and Checking Operating Pressure
  3. Gas Rate from the Meter: The Calculation
  4. Flame Picture and Safety Devices

Revision and Exam Prep

pp. 63-66
  1. The Whole Installation on One Page
  2. Numbers to Have at Hand
  3. Common Mistakes Before an Inspection
  4. How to Use This Book Before the Exam

Who This Book Is For

You're an apprentice in your final years

The whole gasfitting syllabus in the order the gas flows, so every rule from the TAFE notes has a place and a drawing.

Your licence exam is coming up

One page per topic to revise at a glance, plus the practice book to test yourself and see which page to go back to.

You already do plumbing and gas work

Print it and keep it in the ute: pipe materials, soundness test steps, flue clearances and commissioning, ready before the inspector arrives.

Plus: 2 Free Books

Gasfitting Exam-Style Questions: Practice Book with Answers
BONUS 1

Gasfitting Exam-Style Questions: Practice Book with Answers

Test yourself topic by topic with exam-style questions, each answer explained with the page and drawing it comes from, so you know exactly what to revise again.

15 Common Gasfitting Mistakes: Before and After
BONUS 2

15 Common Gasfitting Mistakes: Before and After

See the most common errors on real installations drawn side by side with the correct version, from flue terminal distances to missing isolation valves, so you spot them before an inspector does.

30-Day Guarantee

30-day guarantee: if a file doesn't open, if the content isn't what the product page describes, if you were charged twice or the email never arrived, write to us and we'll refund you in full. You pay once. No subscriptions.

Frequently Asked Questions

Is it for me if I've been a plumber for years and I'm now adding gasfitting?

Yes. It doesn't explain what a tap is: it goes straight to gas, from the meter or cylinder to the flue, in one fixed order. It's written for Australia and AS/NZS 5601.1, with kPa, MJ/h and metres, no inches or psi.

Where does the content come from?

From AS/NZS 5601.1 (current edition), which is used across Australia, and the Victorian gasfitting licence and registration requirements. If you're licensed in another state, the standard is the same, but check your state regulator's local rules and exam requirements. The tables of the standard are not reproduced: the book uses its own drawn examples. Always check the current edition and the manufacturer's instructions.

Is it official material?

No. It's independent study material, not produced, approved or endorsed by Standards Australia or any regulator.

Does it replace the course or the training?

No. It helps you revise what you learn in your training and on the job, but it doesn't replace accredited training, supervised work or the licence, and it doesn't give you a certificate or count towards any unit.

Are the practice questions the ones in the exam?

No. They're exam-style questions written for this book, each answer linked to the page it comes from.

When and how does it arrive?

As a PDF by email, to the address you enter at checkout. The 2 bonus books come with it.

Do I have to pay every month?

No. It's a one-off payment, with no subscription.

Can I have it on paper?

Yes. The PDF is made to print, so you can keep the pages you need in the ute or on the job.

How does the refund work?

You have 30 days. We refund everything if the file won't open, if the book isn't what you see on this page, if you were charged twice or if the email doesn't arrive: just email us.

A$ 39A$ 89
Get the book ยท A$ 39

This is a digital PDF book sent to your email: nothing is printed or shipped.